Tweet
e ovako ...
imam ovaj basic ...
alpina
Diaphram
Material: Kevlar Reinforced Pulp Fiber
Design: 2-Piece Structural Parabolic
Surround
Material: Injected Molded Santoprene®
Design: High Amplitude Mutli-Roll
Spider
Material: Nomex®
Design: Mirrored Progressive
Voice Coil
Material: 180°C High Temp Wire on Spiral Cut Aluminum Former
Design: 4-Layer Dual Voice Coil
Motor Structure
Pole Geometry: Compound Radius Curve (Patent #6,639,993)
Configuration: Radial Vented VC Heat Sink and Airflow Management System (Patent Pending)
Frame
Material: Cast Aluminum
Design: Perimeter Vented Heat Transfer (Patent Pending)
Terminals
Layout: One Side
Design: Heavy Duty 8 gauge Push with Housing, Banana Plug Jumper
Tinsel Leads
Design: Reinforced Layer Spider Integration (Patent #6,810,988)
Gasket
Design: Concealed Mount Gasket System
Power Handling
Power Range: 200 - 500 Watts
RMS Power Handling: 500 Watts
Peak Power Handling: 1500 Watts
Dimensions
Mounting Depth: 195 mm (7.7'')
Mounting Diameter: 275 mm (10.9'')
Displacement: 0.071 cu. ft (Front Mount)
Added Volume: 0.085 cu. ft. (Reverse Mount, Magnet Out)
General
Frequency Response: 25Hz - 500Hz
I sa njime sam dobio kompresionu kutiju od medijapana koja je pravljena po njegovoj lititrazi ..
i za sada se cuje skroz ok ... ali gledam po netu .. sta kako i pitam se da li bi se mozda bolje culo ako napravim ili prepravim ovu kutiju u bas reflex kutiju ...
pa da cujem vasha misljenja .. preporuke ... skice .. resenja ....
imam ovaj basic ...
alpina
Diaphram
Material: Kevlar Reinforced Pulp Fiber
Design: 2-Piece Structural Parabolic
Surround
Material: Injected Molded Santoprene®
Design: High Amplitude Mutli-Roll
Spider
Material: Nomex®
Design: Mirrored Progressive
Voice Coil
Material: 180°C High Temp Wire on Spiral Cut Aluminum Former
Design: 4-Layer Dual Voice Coil
Motor Structure
Pole Geometry: Compound Radius Curve (Patent #6,639,993)
Configuration: Radial Vented VC Heat Sink and Airflow Management System (Patent Pending)
Frame
Material: Cast Aluminum
Design: Perimeter Vented Heat Transfer (Patent Pending)
Terminals
Layout: One Side
Design: Heavy Duty 8 gauge Push with Housing, Banana Plug Jumper
Tinsel Leads
Design: Reinforced Layer Spider Integration (Patent #6,810,988)
Gasket
Design: Concealed Mount Gasket System
Power Handling
Power Range: 200 - 500 Watts
RMS Power Handling: 500 Watts
Peak Power Handling: 1500 Watts
Dimensions
Mounting Depth: 195 mm (7.7'')
Mounting Diameter: 275 mm (10.9'')
Displacement: 0.071 cu. ft (Front Mount)
Added Volume: 0.085 cu. ft. (Reverse Mount, Magnet Out)
General
Frequency Response: 25Hz - 500Hz
I sa njime sam dobio kompresionu kutiju od medijapana koja je pravljena po njegovoj lititrazi ..
i za sada se cuje skroz ok ... ali gledam po netu .. sta kako i pitam se da li bi se mozda bolje culo ako napravim ili prepravim ovu kutiju u bas reflex kutiju ...
pa da cujem vasha misljenja .. preporuke ... skice .. resenja ....
Comment