Kako povezati kopir aparat na komp

[JAPANX]

nikako ne mogu da mu doakam a nemam nikakvo uputstvo niti iskustvo...

ako neko zna, on i ricoh affilio 200 su radjeni isti ali pod razlicitim imenima

stvarno mi treba pomoc, priznajem

[vujke]

Pa jel ima neki prikljucak, USB ili LAN? U prvom slucaju ti treba drajver od njega a u drugom samo da znas koja mu je IP adresa da bi ga namestio kao mrezni stampac.

[uglavnom.bezopasni]

Dok se ne raspitam detaljnije, prvo pitanje je da li se vezuje na usb, ako je tako onda postoji mogućnost da si ga povezao pre nego što si instalirao drajvere i sad te zeza (kao i svi hp štampači prvo drajver pa tek kad instalacija kaže da vežeš štampač, onda).

Ako je to slučaj treba u registiju obrisati određenje ključeve za njega.
Prvo u device manageru pogledaš u details instance id nešto kao USB\Vid_0457&Pid_0150&Rev_0100 i onda to nađeš u regedit-u ali samo u delu (biće na još puno mesta) HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\U SB i obrišeš, pa onda probaš prvo driver...

[deki-ascona]

daj mail pa da ti posaljem i drajvere

************************************************** ***********************
README file for Ricoh Aficio 200/250 PCL printer driver for
Windows(R) NT 4.0.
February 3, 2000
Version 2.0
Copyright (c) 1997-2000 RICOH COMPANY, LTD.
All rights reserved.
All brand names and product names mentioned in this document are
trademarks or registered trademarks of their respective companies.
************************************************** ***********************

This README file has the following sections:

(I) Introduction
(II) Software license agreement
(III) Files contained in this package
(IV) Installation
(V) Application notes and tips


(I) Introduction
================

This file describes how to set up your printer driver and contains the most up-to-date information that was available at release. Please read the software license agreement carefully and see the application notes section for details of known limitations. For information on printer driver settings and features, please check the Help file.

(II) Software license agreement
===============================

YOU, THE END USER, SHALL USE THIS SOFTWARE ("THE SOFTWARE") ACCORDING TO THE TERMS OF THIS AGREEMENT.
BY LOADING THE SOFTWARE INTO ANY COMPUTER, YOU ARE AGREEING TO BE BOUND BY THESE TERMS. IF YOU DO NOT ACCEPT THE TERMS OF THIS AGREEMENT, YOU MAY NOT LOAD THIS SOFTWARE INTO ANY COMPUTER.

Grant of license:
The Software is licensed for use by you for the equipment. You are permitted to the use the Software on any computer which permits electronic access to the equipment. You are not permitted to rent or lease the Software or to transfer your rights under this license to a third party.

Acceptance:
You shall be deemed to have accepted the terms of this Agreement by loading the Software into any computer.

Duration:
This license is effective until terminated. The license will terminate where you fail to comply with the terms of the Agreement. Upon termination, you agree to destroy all copies of the Software and its documentation.

Ownership of Software:
You only own the magnetic media on which the Software has been distributed. It is an express condition of this Agreement that the title and ownership of the Software shall be retained by the owners.

Copying:
The Software and its documentation are the subject of Copyright. You may not make any copies nor cause others to make copies of the software except such copies as are necessary for licensed use and operational security. For this purpose up to three copies may be made. Any such copies are subject to the conditions of this agreement.
You may not modify, adapt, merge, translate, reverse engineer, decompile, disassemble or create derivative works based on the whole or part of the Software or its associated documentation.
You may be held legally responsible for any copyright infringement, unauthorized transfer, reproduction or use of the Software or its documentation.

Limitation of warranty:
THESE RIGHTS ARE YOUR SOLE AND EXCLUSIVE REMEDY, WHETHER IN TORT, CONTRACT, OR OTHERWISE. IN NO EVENT SHALL SUPPLIER, OWNER OF THE SOFTWARE OR ITS LICENSORS BE LIABLE FOR DAMAGES (INCLUDING ANY FOR LOSS OF INFORMATION, PROFITS, SAVINGS OR BUSINESS INTERRUPTION OR OTHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES) ARISING OUT OF THE SOFTWARE OR THE USE THEREOF, OR THE INABILITY TO USE THE SOFTWARE.

Exporting law:
You acknowledge that the export of the Software is governed by the export control laws of the United States and other countries. You agree to comply with all such export control laws.

Governing law and jurisdiction:
If any provision or portion of this agreement shall be found to be illegal, invalid or unenforceable, the remaining provisions shall remain in full force and effect. This Agreement shall be governed by the laws of California, USA and is subject to the jurisdiction of the Federal District courts for the Central District of California by a judge and not a jury.


(III) Files contained in this package
=====================================

README.TXT
RIA250NT.DLL
RIA250NT.INF


(IV) Installation
=================

This printer driver is provided on a 3.5 inch diskette.

1. Insert the "PCL Printer Driver for Windows NT" diskette into the 3.5-inch disk drive on the host computer.

2. Close any applications that are currently running.

3. Click the Start button and select Printers from the Settings submenu. The Printer window is displayed.

4. From the Printers window, double-click on the Add Printer icon. The Add Printer Wizard window is displayed.

5. Select either "My Computer" or "Network printer server" then click on "Next". If you select My computer, select port by checking desired box then click on "Next". If you select Network printer server, select desired network printer then click on "Next".

6. Click on Have Disk. The Install From Disk window is displayed.

7. In the Install From Disk window, type the letter for the drive which contains the installation diskette and click "OK". The printer driver name will appear highlighted.

8. Click on "Next" and follow the instructions on the screen to complete the installation.

9. When "Files Needed" window is displayed, insert "Windows NT CD-ROM" into the CD-ROM drive.
Type the letter for the CD-ROM drive and ":\I386". (e.g. "E:\I386")


(V) Application notes and tips
==============================

1. Due to the limitation of the unidriver under Windows NT 4.0, The help file explains in general and not to be customised to this product.

2. Some application may cause Windows NT stalled, contact application vendor to solve problems.

3. Paper source must be explicitly selected Tray1-4 or LCT, in order to make staple funtion works.

4. To avoid problems in general, make sure that there is plenty of free disk space.

[JAPANX]

sve je to lepo ljudi ali ja ne znam NA STA se kaci... znaci imaju neki dzekovi ali ih ja ne prepoznajem

evo ih

[uglavnom.bezopasni]

Svi spominju neki model d420 NETWORK, sad da li ti fali neki modul za vezivanje na mrežu probaću da nađem, onda se treba telnetovati na njega i podesiti i IP i SUBNET, pa tek onda drajveri...

[JAPANX]

kad bih znao... znam sigurno da postoji opcija kacenja na komp i kacenja na telefonsku liniju zbog slanja faksa ali stvrno nemam ideju... obilazio sam oko njega, ima mnogo nekih otvora kroz plastiku, za sada sam nasao samo ova dva dzeka jer je kopir ogroman kao prosecni sto za kompjuter...

[overspeed]

Definitivno ti pre svega treba adapter ali obzirom na to da je ova tehnologija u novije vreme poprilichna retkost pitanje je kako i gde naci adapter. Ovo mi lichi na neke modele za US trzhishte, koji su uvek sa specifichnim napajanjima, prikljuchcima i standardima.
Elem, adapter je prva stvar, jer u ovaj plug sa druge slike ne mozhesh da metnesh nishta shto je trenutno aktuelno shto se umrezhavanja tiche. Posle toga trebace ti i neki telnet klijent, ali njega cesh lako iskpati sa neta.

A ako je ovaj model bash isti kao Ricoh Afilio 200 onda evo ti link dole za download drivera. "Namenski" driver za Nashuatec d420 nisam uspeo da iskopam

http://www.copy-land.com.pl/ster/Aficio200250XP.rar

[JAPANX]

sto se tice drajvera nije problem, ima na sajtu nashuatec kao i uputstva za kopir... samo nema uputsto tipa "uzmi picimici kabl i ubaci u kopir" ilki tako nesto a ovi dzekovi su mi potpuno strani

inace, jedan lik mi je rekao da je to prvi digitalni kopir pa je sigurno neki stari dzek u pitanju

ma sigurno neko zna, ne znam kako se povezuju danasnji... na usb??

[uglavnom.bezopasni]

Kod modernih osnovna varijanta je mreža, a usb kao opcija... ovom tvom definitivno fali kartica (interfejs za povezivanje) i na telefonsku liniju i na mrežu.

Na njihovom sajtu je drajver za NT4, a drajver za XP imaš već u windowsu Ricoh Aficio 200/250 PCL, ali nigde nema slika/text kako/na šta, čime se povezuje...

[JAPANX]

e ovako, otvorio sam mu zadnju stranu i izgleda stvarno fali neka kartica jer ima otvore u plastici za telefonsku liniju i neke konektore a njih nema

evo svi papiri od njega sto imam, nije veliko 2.5mb pa ako neko moze da pomogne

http://rapidshare.de/files/40703872/kopir.rar.html

a evo i slike zadnje strane bez maske(plastike) pa ako prepoznajete

[JAPANX]

znaci nista od povezivanja... jbg

izgleda cu morati da ga chipujem

[Dolke]

Re: Kako povezati kopir aparat na komp

Pozdrav...

Uf bas sam se namucio trazeci po netu za nekim ko ima slican problem, pored celog neta Vas da nadjem, super

E ovako. Imam RICOH Aficio 200 kopir aparat [prestao da se proizvodi 1998. god.] i imam slican problem kao gospodin gore - povezivanje aparata sa racunarom.
Pored onih portova, cije su slike okacene, moj aparat poseduje i standardni DB25, tj printers (Centronics) port, onakav kakav je ranije bio standardan na starijim stampacima...

Racunar na koji zelim da ga povezem ima takodje taj port, OS je windows XP sp2, i nemam onaj poseban interface (PCI karticu) za onaj cudni izlaz o kome je gore bilo reci...

Da li bi to moglo da se poveze samo preko printers porta, i da li bi tako mogao da stampam dokumente?
Hvala, cenim svaku sugestiju i misljenje

P.S. Ako su vam neophodni jos neki detalji i info, samo recite

Dolke

[DraxNS]

Re: Kako povezati kopir aparat na komp

Ako ima printer port i na kopiru i na racunaru, naravno da je moguce povezivanje, ali SAMO pod uslovom da imas odgovarajuci drajver. Da li se isti vec nalazi u XP bazi drajvera ili ga ima na sajtu proizvodjaca.... moraces sam da saznas.... Mada je to mrka kapa ako se sam kopir prestao proizvoditi 1998 godine (Windows 98 SE ) cisto sumnjam da su u fabrici nastavili razvoj drajvera cak do XP-a.

Sve u svemu, fizicka konekcija je moguca LPT>LPT ali bez odgovarajucih "instrukcija" nista od "razgovora".

[uglavnom.bezopasni]

Re: Kako povezati kopir aparat na komp

Koliko se ja sećam ima drajver u XP-u...