Tweet
Pre neki dan sam primetio da prilikom ukljucivanja klime i odabira brzine duvanja ventilatora lampica na ac prekidacu nece da svetli u bilo kojoj brzini ventilatora, i po nekom pravilu se to desava obicno na prvoj i drugoj brzini.
U pocetku sam pomislio da to nekako zavisi od spoljnje temperature, ali izgleda da nije vec na neki nacin prekidac za ventilator nekako izgubi kontakt i ventilator radi na zadatoj brzini ali klima ne radi...tesko objasniti, ali ko ima isti problem razume o cemu pricam....
LM, pretragom po netu naidjem na ovaj tekst:
http://www.mazdas247.com/forum/showthre ... =123678787
Nisam ovo isprobao, ali koliko sam razumeo potrebno je samo stisnuti malo kontakte...samo mi nije bas jasno da je samo to u pitanju, moze li neko da mi razjasni malo tekst posto ga nisam bas dobro razumeo?
Desava li se vama ovo?
U pocetku sam pomislio da to nekako zavisi od spoljnje temperature, ali izgleda da nije vec na neki nacin prekidac za ventilator nekako izgubi kontakt i ventilator radi na zadatoj brzini ali klima ne radi...tesko objasniti, ali ko ima isti problem razume o cemu pricam....
LM, pretragom po netu naidjem na ovaj tekst:
http://www.mazdas247.com/forum/showthre ... =123678787
PROBLEM: A/C light flickers on position 2 and 3
PREVIOUSLY TRIED: Replacing switch, cleaning all contacts
RESULT: Worked for a day or 2....
SOLUTION: 1) Pull out each wire (1 by 1 so there's no color mix-up) using a tiny screwdriver to lift the tiny tab inside each wire housing.
2) Clean each contact with isopropyl alcohol or similar
3) Squeeze the connector closed with pliers
4) Re-install
Before doing this, I noticed that if I would pull the wire harness out a couple of mm, I would lose electrical contact completely (obviously). But what surprised me was that when I would push the connector in SLOWLY to the point of just making electrical contact, only fan speeds 1 and 4 would work. I would have to push the connector in further to engage all fan speeds. After squeezing my contacts, I now have the A/C light completely solid during ALL fan speeds, EVEN when I pull the connector out a few mm. So this worked for me!
Try it and post your results!! Put a STICKY too!!
EDIT: I JUST ADDED A PIC WITH THE PINOUT SHOWING WHICH WIRE CONTROLS WHICH SPEED... THIS MAY HELP YOU ISOLATE THE PROBLEM WIRE...
PREVIOUSLY TRIED: Replacing switch, cleaning all contacts
RESULT: Worked for a day or 2....
SOLUTION: 1) Pull out each wire (1 by 1 so there's no color mix-up) using a tiny screwdriver to lift the tiny tab inside each wire housing.
2) Clean each contact with isopropyl alcohol or similar
3) Squeeze the connector closed with pliers
4) Re-install
Before doing this, I noticed that if I would pull the wire harness out a couple of mm, I would lose electrical contact completely (obviously). But what surprised me was that when I would push the connector in SLOWLY to the point of just making electrical contact, only fan speeds 1 and 4 would work. I would have to push the connector in further to engage all fan speeds. After squeezing my contacts, I now have the A/C light completely solid during ALL fan speeds, EVEN when I pull the connector out a few mm. So this worked for me!
Try it and post your results!! Put a STICKY too!!
EDIT: I JUST ADDED A PIC WITH THE PINOUT SHOWING WHICH WIRE CONTROLS WHICH SPEED... THIS MAY HELP YOU ISOLATE THE PROBLEM WIRE...
Desava li se vama ovo?
, salim se pa kaze samo da izvuces prekidac, ocistis kontakte, i malo stisnes buksne, e to je njemu zavrsili posao, a dali ce tebi neznam valjda oce. Probaj nije to nista komplikovano, izvadi stisni te buksne, a usput mozes da proveris prekidac da li radi kako treba.
) i to preko rupa i cackao sam prekidac tamo amo ali sijalica drzi i ne trepce.
Comment